JVC RX-D412BUJ Instrukcja Użytkownika

LVT1572-010A[UJ]RX-D412BAUDIO/VIDEO CONTROL RECEIVER INSTRUCTIONSCover[UJ].indd 1Cover[UJ].indd 1 06.6.27 2:32:58 PM06.6.27 2:32:58 PM

CAUTIONS:• Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals (6 Ω – 16 Ω).• DO NOT connect more than one speaker to one spe

Connecting video componentsDo not connect the AC power cord until all other connections have been made.7 HDMI connectionIMPORTANT:The HDMI video signa

7 Audio/video connectionIn addition to the HDMI terminals, this receiver is equipped with three video terminals—composite video, S-video, and componen

Do not connect the AC power cord until all other connections have been made.Connecting a DVD recorder or DVD player with its analog discrete output ja

Do not connect the AC power cord until all other connections have been made.Turn off all components before making connections.• When you connect the

Do not connect the AC power cord until all other connections have been made.Turn off all components before making connections.• When you connect the

7 Digital audio connectionThis receiver is equipped with three DIGITAL IN terminals— one digital coaxial terminal and two digital optical terminals—an

USB connectionThis receiver is equipped with a USB terminal on the front panel. You can connect your PC to this terminal and enjoy sound reproduced th

By using Precise Surround Setup, you can optimize the speaker settings easily, quickly and systematically without troublesome adjustments.To obtain th

3 Put on the microphones.• Insert the microphone with “L” into your left ear, the microphone with “R” your right ear.4 Take your usual listening po

G-1Warnings, Cautions, and OthersCaution–– STANDBY/ON button!Disconnect the mains plug to shut the power off completely (the standby lamp goes off).

6 Unplug the earphone-type microphones.• When unplugging the microphones, pull on the plug, not the cord itself.NOTES• Do not press any buttons on

Troubleshooting for Precise Surround SetupWhen problems occur, a message appears on the display during Precise Surround Setup. In this case, refer to

1 Turn on the powerPress STANDBY/ON (or AUDIO on the remote control).The standby lamp goes off and the current source lamp lights in red.To turn o

7 Selecting the video input settingFrom the remote control ONLY:1 Press one of the source selecting buttons to select the source you want.2 Press VI

NOTES• “HDMI” is selectable only when the video input setting is also set to “HDMI” (see page 21).The audio input setting may automatically change if

Turning off the power with the Sleep TimerYou can fall asleep while listening to music—Sleep Timer.From the remote control ONLY:Press SLEEP repeatedly

FM/AM tuner operationsNOTEWhen you have selected “FM” or “AM” by using SOURCE SELECTOR on the front panel, the remote control may not work for tuner o

3 Press the numeric buttons (0 – 9, h10) to select a channel number while the channel number position is flashing.• For channel number 5, press 5.•

XM Satellite Radio operationsNOTEWhen you have selected “XM” by using SOURCE SELECTOR on the front panel, the remote control may not work for XM Satel

7 To tune in to channelsFrom the remote control ONLY:Channel SearchYou can search and tune in to all channels.1 Press XM to select “XM” as the source

FeaturesHybrid Feedback Digital AmplifierRX-D412B features the JVC-exclusive Hybrid Feedback Digital Amplifier. Premium-grade parts and devices, and s

4 Press MEMORY again while the selected preset number is flashing on the display.5 Repeat steps 1 to 4 until you store all the desired channels.To e

Basic settingsTo obtain the best possible sound effect from the Surround/DSP modes (see pages 39 to 44), you need to set up the speaker and subwoofer

Operating procedureOn the front panel ONLY:Before you start, remember...There is a time limit in doing the following steps. If the setting is canceled

7 Setting the surround back speaker(s)—S BACK OUTRegister the number of the surround back speaker(s).SB OUT 1SPK Select when you use a single surround

Activating the EX/ES/PLIIx setting—EX/ES/PLIIxDepending on this setting, available Surround modes for digital multi-channel software vary—EX/ES/PLIIx

Setting bass sound7 Setting subwoofer output—SUBWOOFER OUTThe subwoofer emits the LFE signals* and the bass elements of each speaker set “SML (small).

Setting the digital input (DIGITAL IN) terminals—DIGITAL IN 1/2/3When you use the digital input terminals, register what components are connected to w

Operating procedureOn the front panel:Before you start, remember...There is a time limit in doing the following steps. If the setting is canceled befo

Adjusting the speaker output levels• SUBWFR LVL (subwoofer output level)• FRONT L LVL (left front speaker output level)• FRONT R LVL (right front s

Reinforcing the bass—BASS BOOSTYou can boost the bass level—Bass Boost.• Once you have made an adjustment, it is memorized for each source.• You can

Table of ContentsParts identification ...3Getting started ...

7 Adjusting the center channel localization for Pro Logic IIx Music and Pro Logic II Music—CENTER WIDTHThis setting is available when Pro Logic IIx Mu

Creating realistic sound fieldsReproducing theater ambienceIn a movie theater, many speakers are located on the walls to reproduce impressive multi-ch

Dolby Pro Logic IIxDolby Pro Logic IIx is another multi-channel playback decoder to convert not only multi-channel software but 2-channel software int

Introducing the DSP modesThe sound heard in a concert hall, club, etc. consists of direct sound and indirect sound—early reflections and reflections f

Using the Surround/DSP modesAvailable Surround/DSP modes vary depending on the speaker settings and the incoming signals. See the table below.• The n

Activating the Surround/DSP modesAvailable Surround/DSP modes vary depending on the speaker settings and the incoming signals. For details about the S

7 Selecting the Surround/DSP modesFrom the remote control:1 Select and play any source.• Surround/DSP modes are not available when multi-channel PCM

NOTES• When connecting the receiver and a TV with the AV COMPU LINK EX terminal by using a component video cable, you cannot use Automatic selection

7 Connecting procedure1 If you have already plugged your VCR, DVD player, TV, and this receiver into the AC outlets, unplug their AC power cords firs

Operating other JVC productsYou can use the supplied remote control to operate not only this receiver but also other JVC products.• Refer also to the

Parts identification7 Remote controlSee pages in parentheses for details.1MUTING button (22)2Standby/on buttons (16, 20, 47 – 51) AUDIO, DVR/DVD , VC

7 DVD recorder or DVD playerAfter setting the mode selector correctly, you can perform the following operations on the DVD recorder or DVD player.See

Operating other manufacturers’ productsBy changing the transmittable signals, you can use the supplied remote control to operate other manufacturers’

To change the transmittable signals for operating a VCR1 Press and hold VCR .• Keep the button pressed until step 3 is finished.2 Press VCR.3 Ent

To change the transmittable signals for operating a CATV converter or DBS tuner1 Press and hold DBS/CATV .• Keep the button pressed until step 3 is

TroubleshootingUse this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC service cente

PROBLEM POSSIBLE CAUSE SOLUTIONRemote controlThe remote control does not operate as you intend.The remote control is not ready for your intended opera

Specifications7 AmplifierOutput PowerAt stereo operation:Front channels:110 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 0.8% t

7 HDMIHDMI Input (Ver. 1.1): VCR(DBS), DVR/DVDHDMI Output (Ver. 1.0): MONITOR OUT7 FM tuner (IHF)Tuning Range: 87.5 MHz to 108.0 MHzUsable Sensitivity

0706RYMMDWJEINEN© 2006 Victor Company of Japan, LimitedAUDIO/VIDEO CONTROL RECEIVERRX-D412BMains (AC) Line Instruction (not applicable for Europe, U.S

See pages in parentheses for details.Front Panel1 STANDBY/ON button and standby lamp (16, 20)2CC CONVERTER button (23)3SETTING button (30)4ADJUST butt

See pages in parentheses for details.Rear Panel1Power cord (14)2VOLTAGE SELECTOR (6)3HDMI terminals (9)VCR(DBS) IN, DVR/DVD IN, MONITOR OUT4AV COMPU L

Before installation7 General precautions• Be sure your hands are dry.• Turn the power off to all components.• Read the manuals supplied with the co

NOTES• If the AM loop antenna wire is covered with vinyl, remove the vinyl while twisting it as shown on the right.• Make sure the antenna conductor