Jvc RX-6010RBK EN Instrukcja Użytkownika

For Customer Use:Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information

7Connecting the Power CordBefore plugging the receiver into an AC outlet, make sure that allconnections have been made.Plug the power cord into an AC

8Basic OperationsThe following operations are commonly used when you play any sound source.Turning the Power On and Off (Standby)On the front panel:To

9CD TAPE/CDRSOURCE NAMEFM/AMTAPE/CDRFM/AMCD–+VOLUMEMASTER VOLUMESelecting different sources for picture and soundYou can watch picture from a video co

10Adjusting the Subwoofer Output LevelYou can adjust the subwoofer output level if you have selected“YES” for the “SUBWOOFER” (see page 11).Once it ha

11Basic SettingsSome of the following settings are required after connecting and positioning your speakers in your listening room, whileothers will ma

12Setting the Speakers for the DSP ModesTo obtain the best possible surround sound of the DSP modes, youhave to register the information about the spe

13ST SETTINGCONTROLDOWN UPCrossover Frequency SettingSmall speakers cannot reproduce the bass sound very well. So, ifyou have used a small speaker for

14TSETTINGCONTROLDOWN UPDIGITAL 2 terminal settingDIGITAL 1 terminal settingDigital Input (DIGITAL IN) TerminalSettingWhen you use the digital input t

15Storing the Basic Settings andAdjustmentsYou can assign and store different sound settings for each differentplaying source. By using this function,

16Receiving Radio BroadcastsYou can browse through all the stations or use the preset function to go immediately to a particular station.2. Press MEMO

G-1Warnings, Cautions and OthersIMPORTANT for the U.K.DO NOT cut off the mains plug from this equipment. If the plugfitted is not suitable for the pow

17FM/AMSelecting the FM Reception ModeWhen an FM stereo broadcast is hard toreceive or noisyYou can change the FM reception mode while receiving an FM

18Using the RDS (Radio Data System) toReceive FM StationsRDS allows FM stations to send an additional signal along with theirregular program signals.

19From the remote control:1. Press PTY SEARCH whilelistening to an FM station.“PTY SELECT” flashes on the display.2. Press and hold PTY +or PTY – unti

20When an emergency broadcast (ALARM signal) is sent from anFM station:The receiver automatically tunes in the station except in thefollowing cases:•

21Using the DSP ModesThe built-in Surround Processor provides two types of the DSP (Digital Signal Processor) mode — Surround mode andDAP (Digital Aco

22BUTTONSURROUND MODE(On the remote control)BUTTONSURROUND ON/OFF* DSP MODE(On the front panel)MODE SURROUND ON THEATER LIVE CLUB DANCE CLUB HALL PAVI

23Available DSP Modes According to the Speaker ArrangementAvailable DSP modes will vary depending on how many speakers are used with this receiver.Mak

2465 – CENTER ++1010 – REAR•R +ENTERMENU98 – REAR•L +1TEST5. Adjust the speaker output levels.• To adjust the center speaker level, pressCENTER +/– (f

25SOUNDSURROUNDSURROUNDMODECONTROLDOWN UPTEST TONE L(Left front speaker)TEST TONE LS(Left rear speaker)TEST TONE RS(Right rear speaker)TEST TONE C(Cen

26DSP MODESOUNDMENU98 – REAR•L ++1010 – REAR•R +ENTER4EFFECTSURROUNDSURROUNDMODEAdjusting the DAP ModesOnce you have adjusted the DAP modes, the adjus

G-2SAFETY INSTRUCTIONS“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”This equipment has been designed and manufactured to meet international safety

27SURROUNDSURROUNDMODESURROUND ON/OFFSURROUND ON/OFFDSP MODEDSP MODEActivating the DSP ModesYou can use only one DSP mode at a time. When a DSP mode i

28COMPU LINK Remote Control SystemThe COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor onthe rece

29Operating JVC’s Audio/Video ComponentsYou can operate JVC’s audio and video components with this receiver’s remote control, since control signals fo

30Operating Video ComponentsIMPORTANT:To operate JVC’s video components using this remote control:• Some JVC VCRs can accept two types of the control

31TroubleshootingUse this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVCservice center

32SpecificationsAmplifierOutput PowerAt Stereo operation:Front channels: 100 W per channel, min. RMS, driven into 8 Ωat 1 kHz with no more than 0.9% t

EN0301NHMMDWJEINJVCVICTOR COMPANY OF JAPAN, LIMITEDRX-6010&6012R[B]COVER_f 01.1.9, 5:51 PM2

1Table of ContentsParts Identification ... 2Getting Started... 3Before Inst

2Parts IdentificationBecome familiar with the buttons and controls on the receiver before use.Refer to the pages in parentheses for details.Front Pane

3Getting StartedThis section explains how to connect audio/video components and speakers to the receiver, and how to connect thepower supply.Before In

4ANTENNAAMLOOPFM 75 COAXIALAMEXT231Snap the tabs on the loop into theslots of the base to assemble theAM (MW/LW) loop.Outdoor single vinyl-covered w

5Connecting the subwoofer speakerYou can enhance the bass by connecting a subwoofer.Connect the input jack of a powered subwoofer to theSUBWOOFER OUT

6Video component connectionsUse the cables with RCA pin plugs (not supplied).Connect the white plug to the audio left jack, the red plug to theaudio r